foxbody1978 on eBay

About

Location: United StatesMember since: Aug 04, 2013

Feedback ratings

Last 12 months

Positive94- positive feedback in last 12 months

Neutral0- neutral feedback in last 12 months

Negative0- negative feedback in last 12 months

All feedback (1,347)

oemcycles (569064)- Feedback left by buyer.
Past month
Verified purchase
Wonderful buyer, would recommend!
*****- Feedback left by buyer.
Past month
Verified purchase
Hope to deal with you again. Thank you.
asun_partshouse (25608)- Feedback left by buyer.
Past month
Verified purchase
Thank you. Let me know if you need anything else.
*****- Feedback left by buyer.
Past month
Verified purchase
Thank you for an easy, pleasant transaction. Excellent buyer. A++++++.
hebli_7 (15606)- Feedback left by buyer.
Past month
Verified purchase
Hope to deal with you again. Thank you.
pgnbearings (59350)- Feedback left by buyer.
Past month
Verified purchase
☆★☆★☆ FIVE STAR EBAYER! EASY AND PLEASANT TRANSACTION! ☆★☆★☆

See all feedback

Reviews (24)

Carburetor for Polaris Sportsman 500 1996 1997 1998

Dec 01, 2022

A great alternative to a worn out OEM Carb

I purchased this carb for a 1997 Polaris Sportsman 500. The original carb was flooding gas into the engine while off AND the drain bowl screw leaked continuously no matter how tight it was. I've bought 2 Chinese carbs for other applications (2 Kawasaki Bayous) and I had to replace the main jet both times in the past. I was proactive with this one because its a real bear to remove and install this carburetor. I opened the float bowl and removed the main jet and sure enough it had a slightly different orifice. It appeared smaller than OEM. As with the other carbs and this one, the OEM main jet threads appeared to be the same but it went in tight (Didn't cross thread) I put it back together and installed on the quad. I was able to reuse the old choke housing and throttle housing. After about 2 hours of total time (Removing, disassembling carbs and reinstalling) the quad is running 99% correctly. To most of the population it would be 100% but I'm like the quad whisperer. It has the slightest cough / hesitation off idle if you are just creep slowly along. Any other throttle position, it is mint. I think the hesitation off idle could be fixed by raising the main jet needle or adding shims. I might do that if it doesn't go away in the summer time. Its 20 degrees outside at time of testing so the colder weather might be affecting the tune. 12/7/22 Update: I ran the quad more and the hesitation went away when it was fully warmed up! So in the end, all I did was swap out the main jet for the original OEM jet and its running great. Time will tell if it holds together but for now I am VERY happy. I will update if any issues arise.

ProMag Ruger LC9 EC9s 9mm 10 Round Magazine Blued Steel, Polymer Sleeve - RUG 17

Apr 25, 2023

10 Round Popper!

I tested 1 full mag (10 rounds) through my EC9S with no issues. I assume it would be good when / if I ever needed it. For the price I think its a good deal. I live in bear country and sometimes don't carry a full size pistol. Having another 3 rounds in the EC9S gives me a bit more confidence while working outside on my property.

Chrome Dress Up Kit SB Ford 289 302 351W Mustang Valve Covers Kit Complete 54383

Feb 27, 2017

Needed new valve covers for my 84 stang.

Bought these for my 84 mustang 5.0. I had leaking valve cover gaskets so decided to replace everything when i came across this deal. Nice quality and easy to install! Really cleaned up the engine compartment! Plus it runs better too! My old pcv valve was bad and when i installed the new one from this kit it really smoothed out the idle! Sounds like a new car! I would recommend these for anyone looking to upgrade their valve covers.

See all reviews