Skip to main content
mbrienza

mbrienza

6.0K items sold
80 followers
Contact
Contact

Shop by category

mbrienza
All categories

All items

Items Per Page
See All

About

I am the largest buyer / collector of the following:
1982-1992 F Body (3rd Gen Camaro)
1984-1996 Y Body (C4 Corvette)
1982-1996 Chevrolet Dealership items
GM Motor Sport items
Players Challenge Race Series items
I pay the HIGHEST prices
PLEASE contact me if you have ANYTHING
Location: United StatesMember since: Jan 23, 1999

Feedback ratings

Last 12 months

Positive127- positive feedback in last 12 months
Neutral1- neutral feedback in last 12 months
Negative0- negative feedback in last 12 months

Detailed seller ratings

Average for the last 12 months
Accurate description
4.9
Reasonable shipping cost
4.7
Shipping speed
5.0
Communication
5.0

All feedback (4,930)

  • n***a (404)- Feedback left by buyer.
    Past month
    Verified purchase
    This seller could give a master's class on how to package an item. Flawlessly packed and shipped very quickly. Item was exactly as described and communication was prompt and courteous. I hope to deal with them in the future.
  • y***t (899)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Excellent value and quality. Great communications and super fast shipping. Item arrived on time, well packaged and in perfect condition. Highly recommended seller. Perfect transaction. Hope to do business with you again,
  • 0***8 (815)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Nice New Old Stock (NOS) Vintage 5-Gallon Metal Fuel-Tank for Tractor, Lawn Mower, Go Kart, Gas Power Equipment: Tank Exactly as Shown / Described; Extremely Well-Packed [Seller Deserves an Extra-Effort Award for All the Effort to Ensure That The Gas Tank Arrived Un-Damaged]; Very Good Shipping Cost Considering the Effort and Materials Use to Protect the Tank; ThankYou Very Much for All Your Effort and for The Tank - It is Perfect for My 12-VDC Generator Project; Thanks Again; Good eBay Seller!
  • -***m (372)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Extremely well packaged, just as described. Very heavy duty hinges will work perfectly for my project. Great seller with excellent communication to the buyer. Would definitely do business again, thank you!
  • h***h (28)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    Description was accurate if not conservative (item received was better than description). Seller was a great communicator.
  • l***i (1)- Feedback left by buyer.
    Past 6 months
    Verified purchase
    MBRIENZA was excellent to deal with. He was very helpful in making sure that I have the correct wheel for my car. Also, the pictures of the wheel were accurate. He sent out the wheel for delivery in a quick manner. The wheel was wrapped to perfection. I would buy from him again!
See all feedback
Reviews (3)
3M - SI-1 Romex Cable Stacker 25 Pack
Apr 21, 2020
Better than the other brands
Other brands are brittle or too soft to hold the max number of wires. I am a professional contractor and 3M is the ONLY brand I use.
DREMEL TR750 3-PIECE CARBIDE STRAIGHT ROUTER BIT KIT FOR DREMEL TRIO TOOL NEW
Nov 07, 2015
Does NOT fit standard Dremel Collet but PERFECT to use in Roto-Zip Tool
I'm a professional carpenter and needed to make dozens of small rabbet cuts in custom cabinets I'm building. The wood surfaces were small so my large router base hung over both sides and tipped. Because of the amount of cuts I need to make i would normally make a jig to hold the piece & support the router but I have it set in a Leigh Pro-FMT jig for making mortise & tenons. I would need to remove the router from the jig AND the bit from the router every time I made a mortise & tenon joint and fit it together to locate the rabbet on the pieces. I have a Dremel tool with the plunge router base attachment which would work without tipping plus I could keep both tools dedicated to their setups saving LOTS of time. I wasn't aware these shanks were too big to fit into the collet of the standard Dremel but they are the perfect size for a Roto-Zip tool. I ONLY use FREUD router bits but they dont have these small diameter shanks so I bought these since they are full carbide. They dont seem to be balanced well so they arent as chatter free as FREUD, which makes the tool vibrate but when used at the slowest speed its not too bad and still moves through the stock cleanly without tearout. They do build up heat really quickly which lets pitch build up so I clean the cutting wings after each cut. After using the 3/8" bit to make 22 three inch long cuts X 3/8" deep in hard maple it is still holding a sharp edge and making cuts as good as the first pass. Keep in mind that these DO NOT FIT the normal Dremel tool due to the larger diameter shank. Just wish they were made in USA.
7-1/4" Magnesium Hypoid Saw Makita 5377MG New
Jun 06, 2017
Not like the made in Japan original; CHEAP Chinese quality didnt work right out of the box!
I went into business as a professional contractor in 1993 and bought the first design of this saw 5077B in May of 1992. I used the heck out of it until March 2017 when the gear started to slip. Sadly Makita discontinued the parts for it so I figured I got my moneys worth and would buy a new saw. After all with this kind of lifespan I probably would retire and it would still be working so the $275 was a relative bargain. NO SUCH LUCK! Right out of the box you could tell it was cheaply made. Looked like some kind of transformers toy with chrome trim pieces, black rubber grips blue rubber levers, and an oddly shaped top handle. All the adjusting levers were rubber coated which are sure to tear after a few days on a jobsite. The trigger has a guard so if you plan on working outside in the cold and need to wear gloves youre going to have to cut a finger off your trigger hand glove or youre not going to be able to use it unless you have tiny hands. I tried it on a few pieces of ply and 3" thick LVL and either the brake didnt work. Makita said to use it more to burn it in but it didnt work after 15 minutes of use. NEVER had a problem with the 5077B other than replacing the cord about 10 times from yearly wear. Maybe you will be happy with it if you never used the old Makita but after 24 years of using the old model I cant see why they would make it so cheap. The Made in China on the label pretty much sums it up. Might be good for occasional work but I doubt it would last a year on my job and at that price I wasnt willing to gamble. Makita got it back the next day and I bought a Skil. It too is made in China but is much beefier than this toy. Been using the Skil for 3 months and I'm glad I sent this back. Almost all my tools are Maikta but they are now breaking and I'm switching to Festool (who doesnt make a wormdrive) TERRIBLE move to go to China Makita; you lost a loyal customer and I wont be returning until you go back to making them with QUALITY in Japan!
1 of 4 found this helpful
See all reviews

About

Use this space to tell other eBay members about yourself and what you’re passionate about. Give people more reasons to follow you!275/1000